- #Spinrite 6 data recovery upgrade
- #Spinrite 6 data recovery full
- #Spinrite 6 data recovery Pc
- #Spinrite 6 data recovery windows
This is not something we have started work on, but it has a high and growing priority.
#Spinrite 6 data recovery upgrade
The upgrade to v6.1 (and any other "dot releases") of SpinRite will be no-charge and all registered owners of SpinRite will be informed as soon as v6.1 is available. Since this is a rapidly growing problem for SpinRite, due to the market's rapid success and uptake of of SATA drives, we are considering the development and release of v6.1, which will cure this problem, sooner rather than later. As mentioned above, all of SpinRite's maintenance and data recovery operations will work even so, but SpinRite's continuous on-the-fly SMART polling will not be available for those drives. If SpinRite is not showing SMART data for your SATA drive(s) and your motherboard's BIOS does not offer any SATA compatibility options, or if you're using an add-on SATA controller which is not showing SMART data, there is not currently any way to force SpinRite to access SMART data of drives at non-standard hardware locations.
Your motherboard's mode will determine which drives are visible to SpinRite.
/grc-spinrite-6-5977653522fa3a001096d897.png "spinrite 6 data recovery")
Note that while your motherboard is configured in "Legacy" or "Compatibility" mode one or more of your SATA drives will replace any IDE/ATA drives that have been "mapped over" for the sake of compatibility.
#Spinrite 6 data recovery windows
These options have been created to support older operating systems, such as Microsoft Windows 9x family, which are incompatible with SATA drives unless they are "mapped" into the traditional IDE hardware locations.Īlthough this is the first thing we will be fixing with the v6.1 release of SpinRite, the first v6.0 release of SpinRite has the same limitation as earlier versions of Windows and other operating systems. These options are typically called "Legacy" or "Compatibility" mode. The BIOS of most SATA motherboards contains SATA configuration options that can be used to cause the hardware registers of new SATA drives to "appear" in the locations occupied by traditional parallel IDE/ATA (PATA) drives. This is what's necessary for SpinRite to obtain SMART data from SATA drives when it otherwise would not be able to. In situations where SpinRite is not obtaining and reporting an SATA drive's SMART data, altering an SATA motherboard's settings can often allow SpinRite to obtain a lower-level "hardware register connection" to SATA drives. So, it's an added bonus when it's available. While this does not limit the strength of SpinRite's maintenance and data recovery, SpinRite's on-the-fly interpretation of "raw" SMART data often provides useful, detailed and sensitive feedback about the current operating condition of SMART-capable drives. But some default SATA configurations can limit SpinRite's ability to also obtain and display the drive's SMART data.
#Spinrite 6 data recovery full
SpinRite performs full maintenance and data recovery operations upon all SATA drives. I think I found your answer only at the end after trying various options, just reading from grc.com (I should have done it before): Wow be careful with those mosquito flies, must be hot over there!! I've heard malaria condition lasts for life.
#Spinrite 6 data recovery Pc
One thing I can tell is that when a computer is too hot from the start is a signthat the processor is working like crazy to get the pc running, if Spinrite says it's your drive doing this then there is something not good and if hardware CPU temp is ok then it's the drive trying to sort itself out thus generating heat. I never encountered that overheating stuff inside Spinrite but if you can enter the bios of your pc and check hardware temperature you should be able to determine whether the CPU is also high in temperature. I'm off to Sainsbury's right now, later I will try and boot again in Spinrite 6 and check out those screens you say and will post more. you know what's the problem really so you can directly go to option 2 if 4 fails to load for some reason, option 4 is maintenance or health check
Anyway, I would go for option 4 as it is maintenance/health check in your case, although option 2 can also be run to optimize and fix errors along the way, it doesn't do any harm to your data so really it's kind of up to you decide which one you want to run, it's like when you have half an headache and you decide to have a hot drink and take the paracetamol tablet may be later.
0 kommentar(er)
